Zoeller Pump Removal Systems - Rail Systems

Zoeller
Pump Removal Systems - Rail Systems
* Overnight Shipping Available!
Pump Removal Systems - Rail Systems
Vertical EZ Out
Features:
Sewage, storm water and effluent pump systems
For concrete, steel or fiberglass tanks
Allows for removal of pumps from ground level
Cast iron base elbow and positive machine fit with O-ring seal provides a reliable seal
Allows for removal of pumps from ground level.
Features:
Sewage, storm water and effluent pump systems
For concrete, steel or fiberglass tanks
Allows for removal of pumps from ground level
Cast iron base elbow and positive machine fit with O-ring seal provides a reliable seal
Guide rails direct the pump to and from the base elbow. Systems are supplied complete with base elbow, sealing plate, pump discharge elbow and upper rail bracket
All systems use 3/4" schedule 40 pipe rails (not included)
Refer to ZM1710 for installation instructions
#10-0789 lifting bails are required on 6160, 6180, 6280, 6290, 6810/6815 and 6820 models to balance pump and rail plate evenly. Othe rmodels already include proper lifting device.
SQUARE GUIDE RAIL SYSTEMS (1 1/4", 1 1/2" & 2" DISCHARGE) FIELD ASSEMBLED
Economical, reduces time and cost of removing pump
Safety, keeps personnel out of pits and out of contact with contaminants
Inspections made fast and easy
Features:
Single rigid stainless steel square rail design
Stainless steel rail, nuts, bolts, fasteners and lifting bail
Cast iron angle arm bracket and pump quide bracket
Galvanized piping, stainless steel optional
Red brass disconnect fittings with Teflon coated Buna O-ring seal
PVC ball valve
Cast iron check valve
Optional stainless pull rods and lifting cable available
Also available in prepackaged fiberglass basins
*For tanks deeper than 72" a second angle arm bracket P/N 39-0070 is required. Sch. 40 galvanized or stainless steel pipe is used for extending the rail length.
RAIL SYSTEMS (2 1/2" TO 6" DISCHARGE) FIELD ASSEMBLED
Guide rail system for removal and installation of flanged horizontal discharge pumps without getting in or removing fluid from pit.
*1/4" lifting cable not included. See ZM1328 for correct cable.
**One intermediate guide rail bracket is required for every 20 for 3" system or 15 for 4" system, of basin depth. See chart for part number.
3", 4" & 6" FLYGT GUIDE RAIL SYSTEM ADAPTERS
Adapter plates for retrofitting 3", 4" or 6" horizontal discharge pumps to existing Flygt rail systems.
Features:
Cast iron construction
Flange conforms to ANSI B16.10 fully flat/MSS SP-6
For use with all 6400, 61 HD & 6700 series pumps with 3", 4" or 6" discharges and 2" NPT rail pipe
Flange gasket and stainless steel bolts included
MYERS GUIDE RAIL SYSTEM ADAPTER KIT FOR 71 SERIES GRINDER PUMPS
Part number 6039-0071 for Myeres 3, 5 & 7.5 HP rail systems Cap requires special drilling
Guide rails direct the pump to and from the base elbow. Systems are supplied complete with base elbow, sealing plate, pump discharge elbow and upper rail bracket
All systems use 3/4" schedule 40 pipe rails (not included)
Refer to ZM1710 for installation instructions #10-0789 lifting bails are required on 6160, 6180, 6280, 6290, 6810/6815 and 6820 models to balance pump and rail plate evenly. Othe rmodels already include proper lifting device.
SQUARE GUIDE RAIL SYSTEMS (1 1/4", 1 1/2" & 2" DISCHARGE)
FIELD ASSEMBLED
Economical, reduces time and cost of removing pump
Safety, keeps personnel out of pits and out of contact with contaminants
Inspections made fast and easy
Features:
Single rigid stainless steel square rail design
Stainless steel rail, nuts, bolts, fasteners and lifting bail
Cast iron angle arm bracket and pump quide bracket
Galvanized piping, stainless steel optional
Red brass disconnect fittings with Teflon coated Buna O-ring seal
PVC ball valve
Cast iron check valve
Optional stainless pull rods and lifting cable available
Also available in prepackaged fiberglass basins
*For tanks deeper than 72" a second angle arm bracket P/N 39-0070 is required. Sch. 40 galvanized or stainless steel pipe is used for extending the rail length.
RAIL SYSTEMS (2 1/2" TO 6" DISCHARGE)
FIELD ASSEMBLED
Guide rail system for removal and installation of flanged horizontal discharge pumps without getting in or removing fluid from pit.
*1/4" lifting cable not included. See ZM1328 for correct cable.
**One intermediate guide rail bracket is required for every 20 for 3" system or 15 for 4" system, of basin depth. See chart for part number.
3", 4" & 6" FLYGT GUIDE RAIL SYSTEM ADAPTERS
Adapter plates for retrofitting 3", 4" or 6" horizontal discharge pumps to existing Flygt rail systems.
Features:
Cast iron construction
Flange conforms to ANSI B16.10 fully flat/MSS SP-6
For use with all 6400, 61 HD & 6700 series pumps with 3", 4" or 6" discharges and 2" NPT rail pipe
Flange gasket and stainless steel bolts included
MYERS GUIDE RAIL SYSTEM ADAPTER KIT FOR 71 SERIES GRINDER PUMPS
Part number 6039-0071 for Myeres 3, 5 & 7.5 HP rail systems
Cap requires special drilling

Key Features

• Sewage storm water and effluent pump systems
• For concrete steel or fiberglass tanks
• Allows for removal of pumps from ground level
• Cast iron base elbow and positive machine fit with O-ring seal provides a reliable seal
• Allows for removal of pumps from ground level

Storm water pump stations are necessary to remove the excess of water during a rainstorm. They not only remove water, but removes waste and other solid materials. Pump Express stocks several brands and types of storm water pumps.

Additional Information (PDF):

Pump Removal Systems - Rail Systems Specification
Pump Removal Systems - Rail Systems Product Brochure